KagiriFpv
Q: can I cut carbon fiber with this
Asked by KagiriFpv on 2022-04-18 10:20:10
KagiriFpv sadly the schematic cannot be posted on the question bar. please follow up on that on the review sections mostly where people will post photos of the product
2021-12-04 01:40:43 Helpful (0)Q: Good day I would like to ask if I have a SBUS driver? And whether it is immediately to send?
Asked by Tm1cha3L on 2018-11-18 02:29:03
KagiriFpv Yes the mamba stack has an sbus driver. Normally the shipping will take close to 2 or 3 days to be shipped and based on your location the shipping time might vary check out mamba stack website on how to set up the sbus receivers such as an rsxr
2021-12-04 01:37:13 Helpful (0)Q: How to connect the dsm spektrum receiver
Asked by Aldron on 2019-01-12 11:53:19
KagiriFpv You need to solder the reciever to the pads set out for the receiver
2021-11-21 01:42:58 Helpful (0)Q: Does this flight controller have an OSD?
Asked by елисей on 2020-12-19 04:38:46
KagiriFpv Yes it does. when wired correctly you could use your transmitter to actually configure on you OSD
2021-11-21 01:42:18 Helpful (0)Q: Is this a stack for 40 bucks?! Really???
Asked by Gilberto on 2018-08-29 10:17:17
KagiriFpv yes it is ...it among the most well priced stacks that still gives out a lot of functions...have it on close to 3 builds now and I haven't regretted using it
2021-11-21 01:41:30 Helpful (0)Q: Can I get the rotating and enter switch ...mine is jammed
Asked by KagiriFpv on 2021-08-18 04:13:08Q: Its compatible with radio master tx16S?
Asked by luissrbc on 2021-06-10 04:49:10
KagiriFpv Yes, it is compatible mainly because your radio master tx16S is a universal transmitter.
2021-06-11 07:32:18 Helpful (0)
KagiriFpv Start by checking if you have any bridging on you solders
2021-03-21 06:25:02 Helpful (0)Q: how many antennas are these?
Asked by BG443537395 on 2020-12-04 05:15:52
KagiriFpv it only come as one antenna ...if you need 2 or more you need to indicate 2 so forth and so on
2020-12-04 05:17:50 Helpful (0)Q: Do you need a power distribution board with this flight controller?
Asked by BG109239251 on 2020-10-10 02:32:04
KagiriFpv No you do not really need one.The stack has its own esc and the flight controller is well laid out for almost anything you would want to solder on
2020-10-11 08:43:12 Helpful (0)Q: Is it spring loaded ? if it is not which one is springloaded
Asked by KagiriFpv on 2020-09-13 02:25:56
FredViau no it's a on or off switch no spring. this is not the failsafe switch
2020-09-13 06:05:37 Helpful (2)
KagiriFpv both black wires are ground the first red wire is 7-24 volts which powers your vtx using battery voltage the other red wire can be used to pass voltage out to you camera that supports 5v out .The blue wire helps you have smart audio and the yellow wire goes into videos .Probably would you mind sharing your flight controller you plan on using then i can help you further.If you use whatsapp app me on +254703500525
2020-09-08 10:41:01 Helpful (1)Q: when will you have it back in stock?
Asked by koes_24 on 2020-04-10 03:38:42
KagiriFpv Itsback if you want to buy ...just checked
2020-07-30 03:40:59 Helpful (0)Q: The best battery for this modulo?
Asked by Vladi Puica on 2019-07-31 03:10:01
KagiriFpv Ipersonally run tattu rline 1350 35c when am doing aggresive flying when i just want to cruise around and master a new skill i use gen ace 2200 25c 3s for more flight time
2020-07-30 03:40:00 Helpful (0)Q: What is the size of the camera with the bracket on?
Asked by rache4free on 2020-07-13 03:07:22
KagiriFpv lengthincreases to 28mm width still at 21.8
2020-07-30 03:36:15 Helpful (0)Q: what is the size of a milli amper for a 3 s battery
Asked by BG223744250 on 2020-07-30 12:28:54
KagiriFpv The size in terms of capacity which is measured in MilliAmps (Mah) will depend on the KV of your motors and the amperes your electronic speed controller can with stand ...Kindly read the kv of your motors the google up the milliamps the motor can take
2020-07-30 03:32:39 Helpful (0)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
