BG161533153
Shred4ac you can install LED kit by yourself.
2021-10-19 03:10:55 Helpful (0)
BG161533153 common thing, if the propeller is damaged that will need to be replaced there's usually spares or at least one spare set that comes with the plane. the nose that broke off can be glued with the foam safe glue like foam tack or some other phone safe glue hot glue in a pinch.
2021-10-15 03:21:37 Helpful (0)
BG161533153 only need some (4) AA size batteries.
2021-10-14 05:02:53 Helpful (0)
BG161533153 38cm nose to tail, 32cm wing to wing.
2021-10-08 09:19:24 Helpful (1)Q: How do I get new Servo Push rods? One of mine fell off.
Asked by jsansonetti on 2021-01-25 10:24:34
BG161533153 If there is a hobby store near you, I would recommend going there and getting the wire. They could make sure you get the correct diameter, and if you are nice, they might mirror the one you have left and put the bends in it for you. The bends could be made with simple needle nose pliers, but there is also a special z bend pliers that makes it simple. If no hobby store, check hardware store for piano wire, or music store. Hopefully this helps.
2021-09-29 07:32:54 Helpful (0)Q: Where can I get spare landing gear?
Asked by BG451554916 on 2020-07-04 12:17:52
BG161533153 my landing gear ripped off on grass landings. I keep it off now and have installed a skid from a gift card to protect the servo. I have had no problems since.
2021-09-19 06:47:15 Helpful (0)Q: I am asking because I saw it on the headline, does it work with F22 raptor, are you sure?
Asked by BG141516204 on 2020-10-02 02:19:44
BG161533153 I think this one is pre programmed for the servos to work as elevator and rudder. The board for the F22 might be the exact same board, but the servos are pre programmed on that one to run as dual elevator. As far as I can tell the F22 does not have any elevon mixing set up, which is a waste. I think this board is compatible with some of the multi protocol transmitter out there that are more hobby grade, like the Jumper T Lite 4in1 or the Radio master T16,and with that combo, I would assume that through the transmitter, you could set up the mixes to work with elevator, elevon, and alerons.
2021-08-11 07:31:23 Helpful (0)
BG161533153 I had the same problem and I noticed that the prop wasn't spinning when the motor was. I switched to the spare prop and it is working fine again. I have several other small RC planes and quads, but have not found a suitable replacement yet that I can buy in bulk. I am sure some quadcopter prop will work. the next time mine comes off, I will measure the shaft so I have the info for replacements.
2021-08-11 05:58:48 Helpful (2)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
bikinidan Molex 51005 2-pin connector 2.0mm pin spacing. Sometimes shown as White Micro Losi or Walkera. And thank you "Lord_jen" for the large amount of incorrect batteries and connectors you have caused to be ordered. Please make yourself known at your local Model Flying Club to claim your richly deserved reward!
2021-11-10 10:43:17 Helpful (0)