jkyim2012jy
Q: Is this gimbal large enough to fit a hero 9?
Asked by jkyim2012jy on 2021-02-11 09:40:20
Q: what gimbal should go with this frame?
Asked by jkyim2012jy on 2021-01-13 02:27:14
Enchantedwas https://www.banggood.com/2-Axis-Brushless-Action-Camera-Gimbal-with-Controller-Support-Remote-Control-for-GoPro-FPV-Racing-RC-Drone-p-908068.html
2021-02-05 09:34:06 Helpful (0)
diver Atthe moment, the firmware allows you to use only Rapidmix or another module. Two rapidmixes can be used at the same time. Rapidfire can be adjusted. You need to extend the pins and change the cover to one that fits the bay (for example 3D printed). You can find details on forums on the internet. It doesn't make sense in my opinion, because Rapidmix is very similar to Rapidfire. In fact, Rapidmix isn't much cheaper.
2021-01-17 07:02:08 Helpful (0)Q: How Long the range is? Of this transmitter with apm 2.8 flight controller ?
Asked by Dhairysheel on 2019-01-15 02:03:36
jkyim2012jy the range in these will probably be about 500 to 700ft max (estimation) with the stock antennas but if you get a directional antenna for whatever frequency you bought the range can be super far
2020-11-06 10:21:47 Helpful (0)Q: are these better than the topsky prime 2s?
Asked by jkyim2012jy on 2019-09-30 08:41:17
46anko46 Absolutely, yes.
2020-06-26 12:40:52 Helpful (0)Q: can i connect av out signal to goggles for better range?
Asked by wejtvincent on 2020-05-21 04:09:48
jkyim2012jy i am not sure you fully understand this product. it is designed to work with an external display so that would be goggles or a screen you cannot use this without one
2020-06-01 01:21:44 Helpful (0)Q: Does the kit version come with servo pushrods and motor mount?
Asked by Johnno on 2019-07-07 08:30:40
jkyim2012jy yes it does
2020-04-08 06:26:08 Helpful (1)
ibrahimdemirdir 36 MM
2020-03-16 02:22:56 Helpful (0)Q: will this work with access protocol? for the x9 lite.
Asked by jkyim2012jy on 2020-01-31 11:30:17
Mrmee Incompatible
2020-02-05 03:55:39 Helpful (0)Q: can you use this with simulators
Asked by jkyim2012jy on 2019-10-18 11:27:25
THUND3RST0RM Yep you just need to connect the cable to your computer and start the simulator
2019-11-09 05:20:43 Helpful (0)
jkyim2012jy a 30 amp esc should be fine to run these
2019-09-26 12:07:40 Helpful (0)Q: do I need external ESCs with this board?
Asked by jkyim2012jy on 2019-09-17 08:03:49
ktulu75 Yes u need them. This borard can be used as a PDB only.
2019-09-18 01:11:05 Helpful (0)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
Ambrosial No.
2021-03-01 02:34:45 Helpful (0)