ehrans
ehrans maybe your gps is too near a motor, or in horizon line with all motors, even maybe you are facing wrong the front point. my first try should be to use a pole mast to keep away the gps of the motor horizontal plane and use the conector to the front. if you use a different position, should be changed on INAv configuration
2022-10-10 12:45:19 Helpful (0)Q: Has anyone had screen rolling when using this cam with Fusion or Rapidfire?
Asked by Dan on 2022-10-01 09:21:21
ehrans is an issue with image binning sistema like fusion, rapidfire, and any like that. it's solved locking the sync on Rx. older versions of rapidfire firmware have an option, newer versions have no option because they directly opted to block the sync because this well known problem. upgrade your rapidfire should be the best option.
2022-10-03 02:13:25 Helpful (1)
ehrans 9g is a size category, not the actual weight of the servo, for example: 9g category size full plastic gears and enclosure vs this full metal gears and enclosure. both are still 9g size, but obviously it's weight is different
ehrans 4s no problem, i 3d printed my own pieces and better than original, look at thingiverse
2022-08-26 03:47:36 Helpful (0)Q: Where can i get the firmware for the 915/868mhz module? its not in the elrs configurator...:(
Asked by Tramberend on 2022-02-08 06:45:02
ehrans it uses the r9m lite firmware
2022-02-13 05:50:49 Helpful (0)
ehrans bind is not equal protocol and variant match, v1 and v2 both usually link also when in lbt. but no channel transmission if everything is not matching perfectly. so the first step is to know exactly which firmware is in your receiver. then select the right mode in the internal multimodule. Also r-xsr are known for do a awful trick. switching sbus to cppm. if you have a blue led always on, you are in cppm mode instead sbus. turn on Rx and long press (10 seconds) the Rx button. after release Rx will do some blinks and turn blue led off. also there is a third possibility. being in F.Port instead sbus+s.port. that means you have to change cabling between Rx and FC. and configure some tricky options in betaflight.
2021-11-22 06:13:58 Helpful (0)
ehrans no current sensor pin on the fc board. it have current sensor resistor in the ESC board. but not in the fc so no current sensing.
2021-10-27 10:53:36 Helpful (0)Q: which oil cps viscosity is needed to refill this shocks? as i can see is very high
Asked by ehrans on 2021-10-26 01:50:38Q: i need spare ribon cable, where can i buy it?
Asked by ehrans on 2019-01-31 01:56:22
CrunkleFloop Your best option is to contact Runcam directly. I've always found them helpful.
2021-03-26 05:32:17 Helpful (0)
ehrans this is for close a serial adapter, this way you can do your electronics tests with just one battery on a multibattery build. people who doesn't know how things work for, are the real dangerous.
2020-11-28 04:28:04 Helpful (3)
We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
ehrans but do not worry, you can change the mode tightening some screws if you want. modern transmitter are an easy change
2023-02-09 03:19:51 Helpful (1)