TUSHEV
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

Makaron 3/3.5 Inch 160mm/180mm Wheelbase X Type Frame kit with 3D Printed Duct for RC Drone
₹2,568.05 ₹5,320.64

Q: Hi, what is the duct material ? Is it TPU or plastic?

Asked by TUSHEV on 2019-11-22 08:49:58

substance606 hey, fellows, where can I get 3d model of ducts? stock one are very bad quality

2020-06-17 02:10:16 Helpful (0)
Submit
Answers (3)
Brotherhobby Avenger 2507 V2 1200KV 6S / 1500KV 5-6S / 1750KV 5S / 1850KV 6S Brushless Motor for RC Drone FPV Racing
₹2,388.66 ₹3,260.70

Q: I have seen that now the Brotherhobby Avenger v2 have come out. Do you have information about these engines? They have very thick windings and look very robust. Could also be suitable for 8 inch propellers like the Garila 2508? The question would be. Are 1200Kv or 1500KV better for 8 inches?

Asked by JB_Copter on 2018-12-19 07:45:01

TUSHEV I wandered the same question. I am putting together a new frame that is capable to fit up to 9” props. I bet this motors in his 1200kv version will be happy spinning 8 and 9 inch propeller, on 4S I mean, may be 5S. I am going to use all in one Xrotor F4 G2 stacks. I ordered my motors directly from Brothers Hobby. The numbers look fantastic so far, it’s going to be around 450grams, just a bit heavier than 6” build!

2018-12-20 07:46:37 Helpful (5)
Submit
Answers (3)
TUSHEV 13/05/2018
It is a awesome aircraft, Just coming from outside and still feel the rush! So tiny and so potent! Lots of power, Fast, good video camera/ TX. smart audio. I could change the position of the camera to the higher holes available as alternative because I am getting lots of garbage i the lens and the props obstruct little the picture. When I set up in the Beta flight I had little trouble with s-bus FRsky RX - do not forget to unable in ports: UART1 Serial RX ! Other wise your s-bus receiver will not function and will not be recognized by Betaflight. Also , use the smart audio to setup power level and channels. the button its not working well and you can not see the indicator since is covered by the top plate. Watch some of "tronage" you tube videos for how to setup!
HGLRC XJB-145MM FPV Racing Drone PNP Omnibus F4 28A 2-4S Blheli_S ESC 25/100/200/350mW Switchable VTX
₹14,387.78 ₹20,964.98
4
Recommendations
Comments (0)

georgi You are the Man! Tnx!

Denes 08/11/2017
Ok this took a while but figured it out at the end. So how to make it work if you use iOS: 1. The QR codes are swapped. The one on the left that says iOS links to the Google play store. Use the one on the RIGHT that says Android(!), that's the correct link to the uTools app on the App Store (in the UK at least). OR, you can simply search in the App Store for for uTools; i've attached the screenshot what it looks like. Install it and open. 2. There is no Eachine icon in the uTools _at_first_. But once you connect the R051 and turn it on (not sure if the order matters, but make sure the little switch on the side is in iOS mode first), it APPEARS. That was a big relief. Once it appeared it stays there even if you disconnect the receiver so it's a kind of self-install by uTools. But obviously, don't unplug it now :) Tap on the icon, and the rest is fairly self-explanatory. Click on the big Play button and you get a white noise unless you are accidentally on the right channel; normally this is the point when you want to turn on your drone and press (and hold for 3 sec) the SCAN button on the R051, watch the scan go through the full frequency range (wish i made a screenshot), it doesn't take too long, and voila! We have picture! The frame rate could be better (on my old iphone 5, might be better on newer models), but not too bad, and the same applies to lag. There is a bit but acceptable. All in all, not too bad for a start, we'll see how it works for the long term :)
Eachine R051 150CH 5.8G FPV AV Receiver Built in Bat For iPhone Android IOS Smartphone Mobile Tablet
₹2,854.72 ₹5,063.15
33
Comments (4)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe