shawnduckham36
shawnduckham36 Well made and simple, Notes for installing: 1. When installing on a municipal water supply with pressures ranges from 1000- 2000 kpa use your own restrictor disk with an OD15mm and ID 3.0 or 3.2mm fitted after your tap. 2. When using restrictor only use on low heat setting, it will be nice and hot and the element will last long. Why? The element is center taped so running it on high is only using half the element and it's driving it harder with more current and less resistance. 3. The earth wire is easy but the neutral wire is not marked it's the wire on the right when you hold the wires tight and look from the top.4. Don't connect the mini shower, blank off the pipe with epoxy. Why not? To get the mini one working nicely you have to over pressurise the main shower head you will see the bottom of the main shower head distort and water start to spray out the sides. 5. The first time to clean the bottom sprayers don't try using the plastic nut in the middle it will strip. Use a belt type oil filter remover tool you can unscrew the whole bottom piece or just the sprayer piece. When you refit it use rubber grease on the silicone o-ring and brass screw, only lightly tighten it then you can just undo it with your hand next time. 6. To get a nice smart job buy this with the matching pipe from the wall ask the seller.
Q: Does is it auto turn off the heater after stop using water?
Asked by nikdano on 2019-02-17 04:29:47
shawnduckham36 Yes the pressure of the water lifts the whole element inside to touch on the contacts when the pressure drops it releases. You have the wires switched around the Earth wire is easily marked and you must always connect this. You need to identify the neutral wire as it's not marked. To do this either open the top cap or hold the wires tight towards you and the neutral wire is on the right. It does not go to the heat setting switch. When you wire it correctly it won't trip your earth leakage.
2022-03-02 05:57:07 Helpful (0)
shawnduckham36 You have the wires switched around the Earth wire is easily marked and you must always connect this. You need to identify the neutral wire as it's not marked. To do this either open the top cap or hold the wires tight towards you and the neutral wire is on the right. It does not go to the heat setting switch. When you wire it correctly it won't trip your earth leakage.
2022-03-02 05:42:08 Helpful (0)
shawnduckham36 You have the wires switched around the Earth wire is easily marked and you must always connect this. You need to identify the neutral wire as it's not marked. To do this either open the top cap or hold the wires tight towards you and the neutral wire is on the right. It does not go to the heat setting switch. When you wire it correctly it won't trip your earth leakage.
2022-03-02 05:38:57 Helpful (0)Q: Normal 16amp fuses will not survive this device if specs are true.. :-)
Asked by Leex70 on 2019-03-01 09:29:06
shawnduckham36 It's over rated but it works like a dream
2022-03-02 05:35:55 Helpful (0)
shawnduckham36 You have the wires switched around the Earth wire is easily marked and you must always connect this. You need to identify the neutral wire as it's not marked. To do this either open the top cap or hold the wires tight towards you and the neutral wire is on the right. It does not go to the heat setting switch. When you wire it correctly it won't trip your earth leakage.
2022-03-02 05:32:51 Helpful (0)
We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
shawnduckham36 Well made and simple, Notes for installing: 1. When installing on a municipal water supply with pressures ranges from 1000- 2000 kpa use your own restrictor disk with an OD15mm and ID 3.0 or 3.2mm fitted after your tap. 2. When using restrictor only use on low heat setting, it will be nice and hot and the element will last long. Why? The element is center taped so running it on high is only using half the element and it's driving it harder with more current and less resistance. 3. The earth wire is easy but the neutral wire is not marked it's the wire on the right when you hold the wires tight and look from the top.4. Don't connect the mini shower, blank off the pipe with epoxy. Why not? To get the mini one working nicely you have to over pressurise the main shower head you will see the bottom of the main shower head distort and water start to spray out the sides. 5. The first time to clean the bottom sprayers don't try using the plastic nut in the middle it will strip. Use a belt type oil filter remover tool you can unscrew the whole bottom piece or just the sprayer piece. When you refit it use rubber grease on the silicone o-ring and brass screw, only lightly tighten it then you can just undo it with your hand next time. 6. To get a nice smart job buy this with the matching pipe from the wall ask the seller.
2022-03-04 02:42:01 Helpful (0)