One of the best mods to my printer works great

One of the best mods to my printer works great

One of the best mods to my printer works great

Very good product, It is working perfectly. Just keep in mind that you can not make a hole through it. It may break the lines. It heats up the bed of my printer in 30 sec from ambient to 90C. You need wiring, a solid state relay is needed. You can connect wires of heater of old heating bed (normally it is 12 or 24 v) as the control signal to solid state relay. Check the voltage of the signal before ordering the solid state relay. they should match. I highly recommend it!

Very good product, It is working perfectly. Just keep in mind that you can not make a hole through it. It may break the lines. It heats up the bed of my printer in 30 sec from ambient to 90C. You need wiring, a solid state relay is needed. You can connect wires of heater of old heating bed (normally it is 12 or 24 v) as the control signal to solid state relay. Check the voltage of the signal before ordering the solid state relay. they should match. I highly recommend it!

Very good product, It is working perfectly. Just keep in mind that you can not make a hole through it. It may break the lines. It heats up the bed of my printer in 30 sec from ambient to 90C. You need wiring, a solid state relay is needed. You can connect wires of heater of old heating bed (normally it is 12 or 24 v) as the control signal to solid state relay. Check the voltage of the signal before ordering the solid state relay. they should match. I highly recommend it!

Goot Product. My HotBed heat now very fast, and not only to 70°C like with the 12V Version, no 110°C is no Problem Goot Solution Goot Price Fast Delivery

Goot Product. My HotBed heat now very fast, and not only to 70°C like with the 12V Version, no 110°C is no Problem Goot Solution Goot Price Fast Delivery

Goot Product. My HotBed heat now very fast, and not only to 70°C like with the 12V Version, no 110°C is no Problem Goot Solution Goot Price Fast Delivery

as described, very good

as described, very good

as described, very good

packed very good and arrived in very good condition. I'll give more feedback after some time of use

packed very good and arrived in very good condition. I'll give more feedback after some time of use

packed very good and arrived in very good condition. I'll give more feedback after some time of use

the only drawback with this item was that the thermistor was shorted out where they had soldered the pins to the wire. measure the resistance in the thermistor before mounting it, as this item has no quality control! it uses a 100k thermistor. it bring my bed to 120°C in a few minutes!!

the only drawback with this item was that the thermistor was shorted out where they had soldered the pins to the wire. measure the resistance in the thermistor before mounting it, as this item has no quality control! it uses a 100k thermistor. it bring my bed to 120°C in a few minutes!!

the only drawback with this item was that the thermistor was shorted out where they had soldered the pins to the wire. measure the resistance in the thermistor before mounting it, as this item has no quality control! it uses a 100k thermistor. it bring my bed to 120°C in a few minutes!!

Unfortunately, the heating on the delivery suffered a lot, the packaging was very bad, the corners are bent and the glue no longer works at the corners, here you have to work yourself. The packaging was too thin and therefore the stability was not guaranteed.

Leider hat die Heizung auf der Lieferung sehr gelitten, die Verpackung war ganz schlecht, die Ecken sind angeknickt und an den Ecken funktioniert der Kleber nicht mehr, hier muss man selber tätig werden. Die Verpackung war zu dünn und somit war die Stabilität nicht gewährleistet.

Unfortunately, the heating on the delivery suffered a lot, the packaging was very bad, the corners are bent and the glue no longer works at the corners, here you have to work yourself. The packaging was too thin and therefore the stability was not guaranteed.