All Messages

Wuehlmaus Laut Datenblatt : Zero-Cross (Nulldurchgang)

2022-12-27 07:03:06 Helpful (1)
Submit
Answers (2)
tamslukcs22 24/01/2021
Összerakása gyors, problémamentes.A LaserGBRL driver telepítésénél szokni kell a sorrendet. Előbb drivert kell telepíteni majd csatlakoztani az USB kábelt. Ezt minden számítógép indításkor el kell végezni.Nálam a gyári leírás szerint beállított fókuszú lézer X tengely irányban nem vágta át a 240gr súlyú fotópapírt, csak gravírozott. Ehhez a GBRL beállításokban a $110 sorban az értéket kb 500-600-650 mm/min értékre módosítottam, több kísérlet után, így már vág.A fényképeken az SMAX/ $110 értékek látszódnak. A feliratozott oldal a vágási oldal.A legkisebb $110 érték ahol már biztosan kivágta a papírt.Füst elszívás ajánlott, ahogy energialánc utólagos beépítése a vezérlés kábeleinek is.A szemvédő plexin látható szenny a teszt során keletkezett. 752 / 5000 Fordítási találatok Assembly is fast and hassle-free. You should get used to installing the LaserGBRL driver. You must first install a driver and then connect the USB cable. This must be done every time the computer is started. In my case, the laser with the focus set according to the factory description did not cut through the 240gr photo paper in the X-axis direction, only engraved it. For this, I changed the value in the $ 110 line in the GBRL settings to about 500-600-650 mm / min, after several attempts, so it's already cutting. The photos show the SMAX / $ 110 values. The labeled side is the cutting side. The minimum value is $ 110 where you have securely cut out the paper. Smoke extraction is recommended, as is the retrofitting of a power chain to the control cables as well.Visible dirt on the eye protection plexin was generated during the test.
7
Recommendations
Comments (3)

tamslukcs22@BG201048363 Szia!Alasergbrl tbbszr munka kzben megszakadt,gy vltottam lightburn-re. Fizet s ,de nagyon megri.

tamslukcs22 24/01/2021
Összerakása gyors, problémamentes.A LaserGBRL driver telepítésénél szokni kell a sorrendet. Előbb drivert kell telepíteni majd csatlakoztani az USB kábelt. Ezt minden számítógép indításkor el kell végezni.Nálam a gyári leírás szerint beállított fókuszú lézer X tengely irányban nem vágta át a 240gr súlyú fotópapírt, csak gravírozott. Ehhez a GBRL beállításokban a $110 sorban az értéket kb 500-600-650 mm/min értékre módosítottam, több kísérlet után, így már vág.A fényképeken az SMAX/ $110 értékek látszódnak. A feliratozott oldal a vágási oldal.A legkisebb $110 érték ahol már biztosan kivágta a papírt.Füst elszívás ajánlott, ahogy energialánc utólagos beépítése a vezérlés kábeleinek is.A szemvédő plexin látható szenny a teszt során keletkezett. 752 / 5000 Fordítási találatok Assembly is fast and hassle-free. You should get used to installing the LaserGBRL driver. You must first install a driver and then connect the USB cable. This must be done every time the computer is started. In my case, the laser with the focus set according to the factory description did not cut through the 240gr photo paper in the X-axis direction, only engraved it. For this, I changed the value in the $ 110 line in the GBRL settings to about 500-600-650 mm / min, after several attempts, so it's already cutting. The photos show the SMAX / $ 110 values. The labeled side is the cutting side. The minimum value is $ 110 where you have securely cut out the paper. Smoke extraction is recommended, as is the retrofitting of a power chain to the control cables as well.Visible dirt on the eye protection plexin was generated during the test.
7
Comments (3)