I bought two MT-8 kits with the CNC upgrades. One to drive and another a few months later as a spare part dispenser. When disassembling the second MT-8, I noticed very negatively that way too much loctite was used. I didn't get some screws loosened and damaged my tool in the process. I had to drill out the screws. The lower suspension brackets (8045 + 8046) were then destroyed. Too much loctite was also used on the c-mounts (8134) and in the hex wheel hub mounts (8086). The screws can only be loosened with very massive screwdrivers. The seal (8265) for the receiver box was missing in both kits. I have installed a 1950 Kv Surpass Taurus 4274 bruhless motor with the standard 13T gear (8195) and standard 48T spur gear (8473) on my MT-8. I recommend installing the stronger motor base (8487). From a 3S Lipo the MT-8 is already quite fast. With a 4S Lipo, wheelies are no problem and the MT-8 becomes a projectile that hardly brings the engine power to the road. The MT-8 then flies over the area and is difficult to control. The construction then reaches its limit. Because of the large wheels, I recommend a powerful 35 kg servo. I also recommend installing the front bumper (8481) and the rear wheel (8482). The front bumper can be upgraded with LEDs. I have a lot of fun with the car, but I would like a little more care when assembling it in the factory. And please don't use so much loctite anymore.

I bought two MT-8 kits with the CNC upgrades. One to drive and another a few months later as a spare part dispenser. When disassembling the second MT-8, I noticed very negatively that way too much loctite was used. I didn't get some screws loosened and damaged my tool in the process. I had to drill out the screws. The lower suspension brackets (8045 + 8046) were then destroyed. Too much loctite was also used on the c-mounts (8134) and in the hex wheel hub mounts (8086). The screws can only be loosened with very massive screwdrivers. The seal (8265) for the receiver box was missing in both kits. I have installed a 1950 Kv Surpass Taurus 4274 bruhless motor with the standard 13T gear (8195) and standard 48T spur gear (8473) on my MT-8. I recommend installing the stronger motor base (8487). From a 3S Lipo the MT-8 is already quite fast. With a 4S Lipo, wheelies are no problem and the MT-8 becomes a projectile that hardly brings the engine power to the road. The MT-8 then flies over the area and is difficult to control. The construction then reaches its limit. Because of the large wheels, I recommend a powerful 35 kg servo. I also recommend installing the front bumper (8481) and the rear wheel (8482). The front bumper can be upgraded with LEDs. I have a lot of fun with the car, but I would like a little more care when assembling it in the factory. And please don't use so much loctite anymore.

I bought two MT-8 kits with the CNC upgrades. One to drive and another a few months later as a spare part dispenser. When disassembling the second MT-8, I noticed very negatively that way too much loctite was used. I didn't get some screws loosened and damaged my tool in the process. I had to drill out the screws. The lower suspension brackets (8045 + 8046) were then destroyed. Too much loctite was also used on the c-mounts (8134) and in the hex wheel hub mounts (8086). The screws can only be loosened with very massive screwdrivers. The seal (8265) for the receiver box was missing in both kits. I have installed a 1950 Kv Surpass Taurus 4274 bruhless motor with the standard 13T gear (8195) and standard 48T spur gear (8473) on my MT-8. I recommend installing the stronger motor base (8487). From a 3S Lipo the MT-8 is already quite fast. With a 4S Lipo, wheelies are no problem and the MT-8 becomes a projectile that hardly brings the engine power to the road. The MT-8 then flies over the area and is difficult to control. The construction then reaches its limit. Because of the large wheels, I recommend a powerful 35 kg servo. I also recommend installing the front bumper (8481) and the rear wheel (8482). The front bumper can be upgraded with LEDs. I have a lot of fun with the car, but I would like a little more care when assembling it in the factory. And please don't use so much loctite anymore.

This is a great deal for awesome truck running 4s with Racestar 4068 brushless and 120amp esc, and DumboRC 6xfg Transmitter and receiver . I have beat this truck pretty hard already and it is holding up. I would suggest upgrading tires and wheels, started cracking first time I was able to play with it. This truck is very solid and half the price of comparable trucks

This is a great deal for awesome truck running 4s with Racestar 4068 brushless and 120amp esc, and DumboRC 6xfg Transmitter and receiver . I have beat this truck pretty hard already and it is holding up. I would suggest upgrading tires and wheels, started cracking first time I was able to play with it. This truck is very solid and half the price of comparable trucks

This is a great deal for awesome truck running 4s with Racestar 4068 brushless and 120amp esc, and DumboRC 6xfg Transmitter and receiver . I have beat this truck pretty hard already and it is holding up. I would suggest upgrading tires and wheels, started cracking first time I was able to play with it. This truck is very solid and half the price of comparable trucks

Very good and sturdy metal frame (to record the bolts). Instructions and accessories closed in a bag to avoid the loss of some rather small parts. Also included the sprocket 13 teeth to be mounted on the motor (and bushing for locking). As well as the motor lock and the support for the servo. Large battery housing measuring 5x13,8cm and 6cm in height. Arrived in 5 working days the tracking details are useless....

Molto buono e robusto telaio in metallo ( da registrare la bulloneria ). Istruzioni ed accessori chiusi in un bag per evitare la perdita di alcune parti piuttosto piccole. Incluso anche il pignone 13 denti da montare sul motore ( e bussola per bloccaggio ) . Come anche il blocca motore ed il supporto per il servo. Ampio alloggio batteria che misura 5x13,8cm e 6cm in altezza. Arrivato in 5 giorni lavorativi i dettagli del tracking non servono a nulla....

Very good and sturdy metal frame (to record the bolts). Instructions and accessories closed in a bag to avoid the loss of some rather small parts. Also included the sprocket 13 teeth to be mounted on the motor (and bushing for locking). As well as the motor lock and the support for the servo. Large battery housing measuring 5x13,8cm and 6cm in height. Arrived in 5 working days the tracking details are useless....

Good value on this product. As the product speaks for itself which shown in the photos. Eveything came was in the box as described. As usual Banggood delivery was 20 days. That’s fantastic.

Good value on this product. As the product speaks for itself which shown in the photos. Eveything came was in the box as described. As usual Banggood delivery was 20 days. That’s fantastic.

Good value on this product. As the product speaks for itself which shown in the photos. Eveything came was in the box as described. As usual Banggood delivery was 20 days. That’s fantastic.

ordine arrivato velocemente,sembra tutto in ordine

ordine arrivato velocemente,sembra tutto in ordine

ordine arrivato velocemente,sembra tutto in ordine

For the money this truck is Unreal!!! if you was to build it in parts it would cost twice the amount! box was Damaged and the body of the Car was a little bit damaged but for what I paid im more than happy! build quality feels really good 👍 I waited just over 30 days from when it left China so not bad atal!! thank you Banggood 🖖🏻 I shall be doing a video for my YouTube Rc Scrapyard once I get the time!

For the money this truck is Unreal!!! if you was to build it in parts it would cost twice the amount! box was Damaged and the body of the Car was a little bit damaged but for what I paid im more than happy! build quality feels really good 👍 I waited just over 30 days from when it left China so not bad atal!! thank you Banggood 🖖🏻 I shall be doing a video for my YouTube Rc Scrapyard once I get the time!

For the money this truck is Unreal!!! if you was to build it in parts it would cost twice the amount! box was Damaged and the body of the Car was a little bit damaged but for what I paid im more than happy! build quality feels really good 👍 I waited just over 30 days from when it left China so not bad atal!! thank you Banggood 🖖🏻 I shall be doing a video for my YouTube Rc Scrapyard once I get the time!

arrived on schedule, the box was a little dented on the outside but inside everything was ok, very nice !!!

arrived on schedule, the box was a little dented on the outside but inside everything was ok, very nice !!!

arrived on schedule, the box was a little dented on the outside but inside everything was ok, very nice !!!

I owned two zd rc cars 1/10 scales (9106 and 9102), with my new 9116 I'm little disappointed. First of all it's not 1/8 scale MT, comapared with the other 1/10 I have for the size was same 1-2 fingers long. I bought new wheels (because one tire of zd 9116 broke) 3.2'' pro line mashers, the rear has 5mm-10mm gap from the main body, the front I have to adjust the steering level because they touches the body when I steering Front and rear diff has little silicone oil and the center was empty, If I remember correct I fill 50K F/R and 100K silicone oil. Shock absorbers same have oil one figure before the top, so I empty them and put 50WT silicone oil team associated. From my mistake at the first race,I forget to lower the brake power on the ESC and flip/crash and broke the rear tire and the body shell. Body shell is thin and wanted 3-4 times to be useless at each time was broke! Space for two battery you can place but I can't see how fit easy and are secure. I have made my custom side and front "covers" to not get easy dust and gravel inside. My setup was - esc hobbywing ezrun max10 120A - 4068 motor 2050kv - jx servo 20kg - 4s lipo For me it doesn't worth it, because it's suppose I bought for 1/8 scale MT, the spaces inside and how the parts (motor, esc servo, battery) it's not clear/big. This MT is more 1/10 scale.

I owned two zd rc cars 1/10 scales (9106 and 9102), with my new 9116 I'm little disappointed. First of all it's not 1/8 scale MT, comapared with the other 1/10 I have for the size was same 1-2 fingers long. I bought new wheels (because one tire of zd 9116 broke) 3.2'' pro line mashers, the rear has 5mm-10mm gap from the main body, the front I have to adjust the steering level because they touches the body when I steering Front and rear diff has little silicone oil and the center was empty, If I remember correct I fill 50K F/R and 100K silicone oil. Shock absorbers same have oil one figure before the top, so I empty them and put 50WT silicone oil team associated. From my mistake at the first race,I forget to lower the brake power on the ESC and flip/crash and broke the rear tire and the body shell. Body shell is thin and wanted 3-4 times to be useless at each time was broke! Space for two battery you can place but I can't see how fit easy and are secure. I have made my custom side and front "covers" to not get easy dust and gravel inside. My setup was - esc hobbywing ezrun max10 120A - 4068 motor 2050kv - jx servo 20kg - 4s lipo For me it doesn't worth it, because it's suppose I bought for 1/8 scale MT, the spaces inside and how the parts (motor, esc servo, battery) it's not clear/big. This MT is more 1/10 scale.

I owned two zd rc cars 1/10 scales (9106 and 9102), with my new 9116 I'm little disappointed. First of all it's not 1/8 scale MT, comapared with the other 1/10 I have for the size was same 1-2 fingers long. I bought new wheels (because one tire of zd 9116 broke) 3.2'' pro line mashers, the rear has 5mm-10mm gap from the main body, the front I have to adjust the steering level because they touches the body when I steering Front and rear diff has little silicone oil and the center was empty, If I remember correct I fill 50K F/R and 100K silicone oil. Shock absorbers same have oil one figure before the top, so I empty them and put 50WT silicone oil team associated. From my mistake at the first race,I forget to lower the brake power on the ESC and flip/crash and broke the rear tire and the body shell. Body shell is thin and wanted 3-4 times to be useless at each time was broke! Space for two battery you can place but I can't see how fit easy and are secure. I have made my custom side and front "covers" to not get easy dust and gravel inside. My setup was - esc hobbywing ezrun max10 120A - 4068 motor 2050kv - jx servo 20kg - 4s lipo For me it doesn't worth it, because it's suppose I bought for 1/8 scale MT, the spaces inside and how the parts (motor, esc servo, battery) it's not clear/big. This MT is more 1/10 scale.

Mega horny car, top processed. a lot of metal.The assembly works very well. I drive the car with a Surpass 4076 2800 Watt motor, 120 Ah ESC and a 11.1 Volt 3S 100 C LiPo. the remote control is from ZD Racing, identical to DumoRC, 400 meters distance, no problem, but I can not fully extend the vehicle, it is just too fast. I only recommend kits without electronic parts, you can choose the components much better and it can be good cheaper. in any case, better components!!!!

Mega geiles Auto, top verarbeitet. viel Metal. Der Zusammenbau geht sehr gut. ich fahre das Auto mit einem Surpass 4076 2800 Watt Motor, 120 Ah ESC und einem 11,1 Volt 3S 100 C LiPo. die Fernbedienung ist von ZD Racing, baugleich mit DumoRC , 400 Meter Distanz, kein Problem, aber ich kann das Fahrzeug nicht voll ausfahren, es ist einfach zu schnell. ich empfehle nur Bausätze ohne elektronische Teile, man kann viel besser die Komponenten selbst aussuchen und es kann gut günstiger sein. auf alle Fälle, bessere Komponenten!!!!

Mega horny car, top processed. a lot of metal.The assembly works very well. I drive the car with a Surpass 4076 2800 Watt motor, 120 Ah ESC and a 11.1 Volt 3S 100 C LiPo. the remote control is from ZD Racing, identical to DumoRC, 400 meters distance, no problem, but I can not fully extend the vehicle, it is just too fast. I only recommend kits without electronic parts, you can choose the components much better and it can be good cheaper. in any case, better components!!!!

good product good price

good product good price

good product good price