Overall this printer is looks great and performs well for now. It's very sturdy and all the parts are metal or acrylic...........except the X Axis belt bracket. The bracket for the Y axis is aluminum. Why they would make such an important part as a belt fastener behind two very hot extruders out of plastic is beyond me. The teeth are softening on the bracket that holds the belt ends from the heat and the X Axis belt slipped out once already. I've only printed three 2mm X 10mm square cubes. To make it worse they don't tell you where to get that 3D model. So an immediate repair is needed before you get started good. The pre-built extruders where uneven. Extruder 2 is lower than Extruder 1. Used shims on one side to try to even it out. Hope that works. The prints I do have look good and it does run very quietly and cleanly. The instructions definitely need updating, but I managed to get it working in the end by switching wires around and changing the configuration file in the firmware. Working with the firmware is easy. Just open Arduino sketch modify configuration.h if needed for motor and endstop behaviors and upload. One hint........all the end stops are X,Y,Z MIN. Even the "Y" axis because the firmware disables the MIN endstops so the program can work. For the price it's a winner, but do a lot of research first if you're new to this.

Overall this printer is looks great and performs well for now. It's very sturdy and all the parts are metal or acrylic...........except the X Axis belt bracket. The bracket for the Y axis is aluminum. Why they would make such an important part as a belt fastener behind two very hot extruders out of plastic is beyond me. The teeth are softening on the bracket that holds the belt ends from the heat and the X Axis belt slipped out once already. I've only printed three 2mm X 10mm square cubes. To make it worse they don't tell you where to get that 3D model. So an immediate repair is needed before you get started good. The pre-built extruders where uneven. Extruder 2 is lower than Extruder 1. Used shims on one side to try to even it out. Hope that works. The prints I do have look good and it does run very quietly and cleanly. The instructions definitely need updating, but I managed to get it working in the end by switching wires around and changing the configuration file in the firmware. Working with the firmware is easy. Just open Arduino sketch modify configuration.h if needed for motor and endstop behaviors and upload. One hint........all the end stops are X,Y,Z MIN. Even the "Y" axis because the firmware disables the MIN endstops so the program can work. For the price it's a winner, but do a lot of research first if you're new to this.

Overall this printer is looks great and performs well for now. It's very sturdy and all the parts are metal or acrylic...........except the X Axis belt bracket. The bracket for the Y axis is aluminum. Why they would make such an important part as a belt fastener behind two very hot extruders out of plastic is beyond me. The teeth are softening on the bracket that holds the belt ends from the heat and the X Axis belt slipped out once already. I've only printed three 2mm X 10mm square cubes. To make it worse they don't tell you where to get that 3D model. So an immediate repair is needed before you get started good. The pre-built extruders where uneven. Extruder 2 is lower than Extruder 1. Used shims on one side to try to even it out. Hope that works. The prints I do have look good and it does run very quietly and cleanly. The instructions definitely need updating, but I managed to get it working in the end by switching wires around and changing the configuration file in the firmware. Working with the firmware is easy. Just open Arduino sketch modify configuration.h if needed for motor and endstop behaviors and upload. One hint........all the end stops are X,Y,Z MIN. Even the "Y" axis because the firmware disables the MIN endstops so the program can work. For the price it's a winner, but do a lot of research first if you're new to this.

Overall a good printer, needs some tweaking to get good results. Had to exchange both z-axis mounts, after about a month because the fixation for the bearings broke on both sides. Don't use the presets in the software from geeetech website, the results are bad. Look on youtube for a tutorial for Slic3r software and start experimenting. After half a role of fillament wasted results were pretty good

Overall a good printer, needs some tweaking to get good results. Had to exchange both z-axis mounts, after about a month because the fixation for the bearings broke on both sides. Don't use the presets in the software from geeetech website, the results are bad. Look on youtube for a tutorial for Slic3r software and start experimenting. After half a role of fillament wasted results were pretty good

Overall a good printer, needs some tweaking to get good results. Had to exchange both z-axis mounts, after about a month because the fixation for the bearings broke on both sides. Don't use the presets in the software from geeetech website, the results are bad. Look on youtube for a tutorial for Slic3r software and start experimenting. After half a role of fillament wasted results were pretty good

Sadly, the delivery was delayed because the ZIP code was wrong and not corresponding with the one I have on file by Banggood. It was not the first time this issue occured.

Sadly, the delivery was delayed because the ZIP code was wrong and not corresponding with the one I have on file by Banggood. It was not the first time this issue occured.

Sadly, the delivery was delayed because the ZIP code was wrong and not corresponding with the one I have on file by Banggood. It was not the first time this issue occured.

good

good

good

They keep clogging. Whatever the temp or feed rate. I tried to clean the nozzle to get rid of this problem. It broke during re-assembly. If you buy this printer, get some new nozzles, too.

They keep clogging. Whatever the temp or feed rate. I tried to clean the nozzle to get rid of this problem. It broke during re-assembly. If you buy this printer, get some new nozzles, too.

They keep clogging. Whatever the temp or feed rate. I tried to clean the nozzle to get rid of this problem. It broke during re-assembly. If you buy this printer, get some new nozzles, too.

After 2 week package arrived AT.

After 2 week package arrived AT.

After 2 week package arrived AT.