Customer Reviews

4.96 out of 5
See all 163 reviews
Write a Review
  • All Reviews (163)
  • Image (44)
  • Video (4)
  • All Star
    • All Star(163)
    • 5 Star(157)
    • 4 Star(6)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (India)
|
Show Original

A part of the review has been auto-translated.

  • 23/07/2016

    This frame is really well build. When assembled, there are holes in the bottom plate that still give you access to most of the screws. The 18mm spacers make it impossible to stack a PDB & FC, since you'll run out of space if you use pinheaders (90 degree ones don't fit either), so i fitted mine with 25mm spacers. Also modified the front a bit (lowered it) and added an adjustable camera mount. I've ordered another 1 for spares (or might build something on it...)

    Comments
    Show Original
  • 28/02/2017

    Ce châssis est magnifique et vraiment bien fait. Mais il n'y a pas d'intérêt d'avoir des bras indépendants et de ne pas pouvoir en acheter en rechange. J'aurais souhaité avec les top plate aussi. https://www.youtube.com/watch?v=7SIdFmk8O_w

    Comments
    Show Original
  • 04/04/2017

    did my first custom build, budget motors, escs and vtx. if you go for it, keep in mind that you need a smaller fpv cam than the usual and vtx and rx should also be ministyle, using a FS-iA6B stripped down without plastic case so i could fit it beneath the vtx.

    Comments
    Show Original
  • 04/09/2016

    После ZMR250 она необычна. Две палубы должны дать улучшение управляемости. Печатнул защиту лучей и моторов, еще по задумке хочу бамперы и что то для защиты аккума, не думаю что эти граммы пойдут в ущерб. Зато позволят быт немного смелее ))

    Comments
    Show Original
  • 21/08/2016

    Not really an easy build due to the "Low profile" on the lack of space to put all the electronics inside, but it is possible to keep the 90 deg pins for the esc wires as you trim the nylon spacers at the right dimensions. (See the photos) The blue painting on the sides of the frame is hand made with a marker. I've just added a pair of column spacers under the battery plate for reliability, the holes are already there, you will need some M3 screws too, also the arms are only 3mm and I think that 4mm would be better. (So only 4 stars in quality) The Lantian E700 700TVL camera fit perfectly as it is designed for this frame. I've put the VTX on the side of the frame for better cooling, but it is possible to put it inside as you use a naked receiver. With these motors and esc's she fly like a beast in 3s and 4s, pretty stable and powerful. I like this little frame so much, the general shape give her the "insect style" that I wanted, the build was not easy but a real pleasure... Here is a list of all the components I've used: Frame: http://www.banggood.com/fr/Lantian-LTX-HEX4-215-215MM-Carbon-Fiber-Mini-Frame-Kit-for-FPV-Racing-p-1055199.html Column Spacers: http://www.banggood.com/Lantian-Checkered-Aluminum-Post-Reticulated-Column-Spacer-M3X18-M3X15-M3X30-M3X35-For-FPV-Racer-Dron-p-1060630.html Camera: http://www.banggood.com/fr/Lantian-E700-700TVL-13-CCD-Sony-Components-FPV-Camera-with-OSD-Board-PAL-p-1049043.html PDB: http://www.banggood.com/fr/Matek-Systems-PDB-XT60-W-BEC-5V-12V-2oz-Copper-For-RC-Multirotors-p-1049051.html Flight controler: http://www.banggood.com/fr/CK-REV6-NAZE32-6DF-Flight-Controller-For-RC-Multirotors-Baseflight-Configurator-p-1030038.html VTX: http://www.banggood.com/fr/TS5828L-Micro-5_8G-600mW-40CH-Mini-FPV-Transmitter-with-Digital-Display-p-1058136.html Antenna: http://www.banggood.com/fr/DAL-5_8G-RHCP-TX-RX-4-Clover-Mushroom-Antenna-with-SMA-Male-RP-SMA-Male-Connector-p-1052449.html Led holder: http://www.banggood.com/fr/LED-Light-Holder-Mount-for-ZMR250-QAV180-QAV250-Lantian210-Frame-Kit-p-1018014.html Leds+Buzzer: http://www.banggood.com/fr/Lantian-2-in-1-WS2812B-LED-And-5V-Active-Buzzer-For-FPV-NAZE32-Skyline32-Flight-Controller-p-1012950.html Motors: http://www.banggood.com/fr/DYS-SE2205-PRO-2300KV-2550KV-3-5S-Lipo-Race-Edition-Brushless-Motor-for-180-210-220-FPV-Racer-p-1059008.html Esc: http://www.banggood.com/fr/FVT-LittleBee-20A-ESC-BLHeli-OPTO-2-4S-Supports-OneShot125-For-RC-Multirotors-p-1007740.html Props: http://www.banggood.com/fr/2-Pairs-DAL-Pro-5045-3-Blade-CWCCW-Propeller-for-FPV-Racing-Muliticopter-p-1056430.html

    Comments
    Show Original
  • 03/11/2016

    One of best frames that i was have!!! realy nice perfomance in air!!!

    Comments
    Show Original
  • 02/01/2019

    hasta horita está funcionando muy bien gracias banggood.

    Comments
    Show Original
  • 14/08/2017

    feels tough and stout crashed it on asphalt twice do to cheap motors. Its a tight fit but a fun frame to build.

    Comments
    Show Original
  • 22/10/2017

    Very good product very nice and quality carbon frame the blue color is my work

    Comments (1)
    Show Original
  • 05/12/2016

    Was soll ich sage, top Qualität, alles passt perfet zusammen, freue mich schon auf den Einbau der Technik.

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go
    recommendation for you
    • ₹5,254.89
    • ₹1,584.23
    • ₹3,628.95
    • ₹3,169.29
    • ₹7,507.35
    • ₹1,751.07
    • ₹6,673.10
    • ₹4,837.77
    • ₹5,838.86
    • ₹1,550.86
    • ₹833.41
    • ₹4,921.19
    • ₹5,421.74
    • ₹1,417.38
    • ₹2,251.62
    • ₹5,831.35
    • ₹4,504.91
    • ₹1,414.04