That's perfect

هذا ممتاز

That's perfect

only got it two days ago. it looks good and it turns on. so that's good.

only got it two days ago. it looks good and it turns on. so that's good.

only got it two days ago. it looks good and it turns on. so that's good.

Maintenance: normal, no problems, no letters, etc. But due to a discrepancy with the site (see below). Below) I estimate at 4 stars. Service of logic: the goods are packed normally; there are no signs of bumps, no impulses of packing; came much earlier than the estimated time - here all the stars that are. I got one (three round steps) out of several nozzles indicated in the advertisement. The order name indicates a capacity of 2 kW, just below, in the specification - 1600 watts. 25% is beyond any reasonable agreement. The regulated temperature is from 50 to 560 degrees Celsius. put a three - stage nozzle (the only one) set the machine in mode 1 at maximum power (low air flow - temperature must be high) and directed the nozzle to a sheet of A4 printed paper (ignition temperature 233 g. Celsius). Kept at a distance of 3 - 5 cm for 3 - 4 minutes. The result: the paper didn't even get charred. I turned on mode 2, directed on his hand with 5 - 7 cm. Result: the air is less hot, but quite tolerable, in the sensations of degrees 60 Celsius. Switched to mode 1, again directed on hand with 10 - 15cm. Result: the air is clearly hotter, but within tolerance. Clearly no 500 - 600 degrees even when the hand approaches the nozzle at a distance of 5 - 6 cm. for 7-10 seconds (quite hot, but burns and charring of hairs are not). Later, I will conduct similar experiments in my laboratory with the required measurements, the results will be sent to the journal U.S. Science to the section Miscellaneous. -------------------------------------------------------------------

Обслуживание: нормально, никаких проблем, никаких писем и т.п. Но из-за несоответствия с сайтом (см. ниже) оцениваю в 4 звезды. Служба логики: товар упакован нормально; следов ударов, порывов упаковки нет; пришел гораздо ранее расчетного срока - здесь все звезды, что есть. Из указанных в рекламе нескольких сопел я получил одно (три круглых ступени). В наименовании заказа указана мощность 2 квт., чуть ниже, в спецификации - 1600 ватт. 25% - это превышает любое разумное соглашение. Также указана регулируемая температура - от 50 до 560 градусов Цельсия. Поставил трехступенчатое сопло (единственное) включил машину в режим 1 при максимальной мощности (малый поток воздуха - температура должна быть высокой) и направил сопло на лист печатной бумаги А4 (температура возгорания 233 гр. Цельсия). Держал на расстоянии 3 - 5 см. в течение 3 -4 минут. Результат: бумага даже не обуглилась. Включил режим 2, направил на свою руку с 5 - 7 см. Результат: воздух менее горячий, но вполне терпимый, по ощущениям градусов 60 по Цельсию. Переключил на режим 1, снова направил на руку с 10 - 15 см. Результат: воздух явно более горячий, но в пределах терпимости. Явно нет 500 - 600 градусах даже при приближении руки к соплу на расстояние 5 - 6 см. в течение 7-10 секунд (довольно горячо, но ожогов и обугливания волосков нет). Позже проведу подобные эксперименты в своей лаборатории со штатными заявленными измерениями, результаты перешлю в журнал США Наука в раздел Разное. -------------------------------------------------- -----------------

Maintenance: normal, no problems, no letters, etc. But due to a discrepancy with the site (see below). Below) I estimate at 4 stars. Service of logic: the goods are packed normally; there are no signs of bumps, no impulses of packing; came much earlier than the estimated time - here all the stars that are. I got one (three round steps) out of several nozzles indicated in the advertisement. The order name indicates a capacity of 2 kW, just below, in the specification - 1600 watts. 25% is beyond any reasonable agreement. The regulated temperature is from 50 to 560 degrees Celsius. put a three - stage nozzle (the only one) set the machine in mode 1 at maximum power (low air flow - temperature must be high) and directed the nozzle to a sheet of A4 printed paper (ignition temperature 233 g. Celsius). Kept at a distance of 3 - 5 cm for 3 - 4 minutes. The result: the paper didn't even get charred. I turned on mode 2, directed on his hand with 5 - 7 cm. Result: the air is less hot, but quite tolerable, in the sensations of degrees 60 Celsius. Switched to mode 1, again directed on hand with 10 - 15cm. Result: the air is clearly hotter, but within tolerance. Clearly no 500 - 600 degrees even when the hand approaches the nozzle at a distance of 5 - 6 cm. for 7-10 seconds (quite hot, but burns and charring of hairs are not). Later, I will conduct similar experiments in my laboratory with the required measurements, the results will be sent to the journal U.S. Science to the section Miscellaneous. -------------------------------------------------------------------